Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Tepa76

Pages: [1]

Code: [Select]
#if defined(__C30__)
    //Disable sleep on suspend!

Thanks a lot this works  :-)

I haven been using 2.03 for all custom project. I would recommend you also use 2.03.

Yes sure, Someday i have to move my main project "beer brewery and fermerter control automation" which is maded with modified fw:1.03
That's tooks me some time. I mean there is quite a lot of changes especially on "circBuffer" codes if remember right!

sheers  :-o


Thanks for the support!

Actually last time when i'll try to track this issue board is rev2 with unmodified std 2.02 firmware

If we think about this... at the moment i have 3 different board's with one std, and 2 others have modified fw... all of them suffering this same issue.
Today i even test this with linux laptop with same results!

If nobody else doesn't have this kind of problem... failure have to be on my side,
but i can't really understand what could causing this! 

Is there something, else that i can test for solving this?

Software / SBC66EC's freezes if computer shutdowns while usb is plugged
« on: October 28, 2014, 11:09:32 AM »
I have found that board get totally jammed when usb are connected with computer "win7 64bit" and i shutdown the computer.
One board is with FW-1.03 and usb power solder jumper are not made (board has powered with external dc supply).
Another have 2.02 and board takes power on the usb, there is usb-hub and it's usb power stays always on.

Just plug the usb on computer and wait that computer acts the usb is connected next shutdown the computer... and board is jammed!
Can this behaviour be fixed?


Software / Suggest e-mail alert function
« on: October 17, 2014, 02:16:09 AM »
I have made a e-mail notification applicatoin that send's me a alerts and information when something happens suddenly.
I have wrote there a function that claims me when board is started, it's a useful to detect a power outages and boots, etc...
Negative result is a boot alert when i made a firmware update. How can i prevent this??

Normally i used a network bootloader and made FW-Update via webpages.
I have found there is code on HTTPMPFSUpload() in "http2.c" but not find the solution on this!


Webserver Firmware / Re: User space on External Flash
« on: September 13, 2013, 05:37:31 AM »
Ok Thanks for the reply.
Now the flash part is working... But another question for handling writes!

What is the best way to buffer the old data before write some new data?

Example: if my configuration data takes the first 3000 bytes in the user space (many different config bytes and strings)
and i want to update the bytes 500-510 with the new data!?


Webserver Firmware / User space on External Flash
« on: May 31, 2013, 10:46:10 PM »
Now i need to take in use the user space for storing the data.

I see at spiFlashWinbond.c contains the functions for accessing the flash!?
Before i start to messing with code can somebody little bit explain what things is have to take a care!
My target is to store the config string on the flash witch is given though the web page.  example (abc123)
After that... board sends that config string over the uart every time on the boot.


SBC66EC & SBC66ECL / Define serialport pins via PPS
« on: September 28, 2012, 12:19:15 AM »

Needed some advice for how to enable serialport1 in following hardware setup.

-PT66EI daughter board and there is iMod im232M module on slot 1

Ill found that routing should be...
RTS =  X8 (RG8)
RX = X7 (RG7)
TX = X6 (RG6)
CTS = X1 (RB1)

So im confused how to config PPS things on right place?
Firmware is "netcruzer_v103"


Pages: [1]