Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - niroblock

Pages: [1] 2 3 ... 10
1
Ethernet Boards (8-bit) / Re: Programming SBC65EC in java?
« on: December 12, 2008, 12:09:03 PM »
hello,


   
want to write a computer program in java, that controls your sbc?
or want to write in Java and link to  pic?




2
Ethernet Boards (8-bit) / Re: Send file from SBC65 server to PC?
« on: May 05, 2008, 01:49:19 PM »
Hi,

I do not understand well what they want to do but
 
if sent by HTTP, TCP, UDP or Serial

"send file" is somewhat generic,

will want to save the page

suffice:

<a href="#" onclick="javascript: document.execCommand('SaveAs','1','mypage.htm');"> Save page </ a>

care only for IE

the http.c has nothing to do!

around so you leave a link where you can learn to send, custom commands, for your "SBC65EC"

http://forum.modtronix.com/index.php?topic=815.msg2450#msg2450

byee.

3
Ethernet Boards (8-bit) / Re: HTTPget Application - v0.1a
« on: May 03, 2008, 07:16:17 PM »

Files project:

  HTTPget_x86_vs2005-SourceCode.zip   All Sorce Code  and Workspace for vs2005 
 
  HTTPget_x86_Win-installer.zip   Binary Install for Win32


   

4
Ethernet Boards (8-bit) / HTTPget Application - v0.1a
« on: May 03, 2008, 07:11:14 PM »
Hi World!


HTTPget

is an application to test the command sent with GET method

Version 0.1 contains :

--) Monitor for the HTTP connector
--) Web browser to test site
--) File transfer (ON / OFF Mode)
--) Auth Request B64 (ON / OFF Mode)
--) Predefined fields for 7 variables (ON / OFF Mode)
--) Auto Save Settings
--) ... and more things ..

I leave with you the entire source code in C#

and also the installable

I hope the people here know appreciate the time and effort devoted to its development

Byee.


5
Ethernet Boards (8-bit) / Re: udp message and sbc65ec
« on: May 03, 2008, 06:46:51 PM »
Hi,

you could publish your firmware?

there is something rare in this ..

anyway, here's an application in C #, which makes what you wanted and many more things.

  has just emerged from the oven.

 
  http://forum.modtronix.com/index.php?topic=969.0

Byee.

6
Ethernet Boards (8-bit) / Re: casting
« on: May 03, 2008, 04:13:26 AM »

7
Ethernet Boards (8-bit) / Re: Password help
« on: May 02, 2008, 12:33:01 PM »
Hi,   


1) "Lost password"

If charges with the firmware: DCI or ICE.'ll Have no problem,

if you want a solution more relaxed, uses a software BruteForce

You advise: "Brutus AE" and "Cain & Abel"

This is the download link (http://www.hack-box.info/bruteforce.html)

2) "C18 Problem"

Reinstall!



byee.

8
Ethernet Boards (8-bit) / Re: MPLAB 3.20 - compatibility
« on: May 02, 2008, 12:11:22 PM »
Hi,

you will be interested

my last test compatibility are as follows:




* C18/C30/C32 tested on the professional versions (not Student Edition)

** To install the MPLAB 8.xx in Win Vista , module VDI gives error

*** Linux with Wine gives registration errors, but it works!

byee.

9
Ethernet Boards (8-bit) / Re: Send file from SBC65 server to PC?
« on: May 02, 2008, 09:41:55 AM »
Hi,

1) Read file

    void main(void)
   { 
        ...
   
        BYTE FileName[]={"TESTPAGE.CGI"};
        FSEE_FILE FileHandle;
        BYTE Dummy;       


       ..
   
       if ( "TODO your code control" ){

             FileHandle =  fileOpen(FileName,0);
             
             if(fileIsValidHandle(FileHandle)){
             
                 do{

                      Dummy = fileGetByte(FileHandle);

                      //only debug  , send to serial
                      serPutByte(Dummy);

                     }while(!fileIsEOF(FileHandle));
             }

            fileClose(FileHandle);



       }

      ...

   


2) send data

if you want send for UDP or TCP Network layer:
 
download this code example
 
http://www.modtronix.com/soft/mxmctcpip/examples_v248.exe

and using the example that best meets your needs


byee.

10
Ethernet Boards (8-bit) / Re: udp message and sbc65ec
« on: May 02, 2008, 09:06:42 AM »
Hi,

the code that you have provided has been tested in various MXBOARD

Quote
tested this code:

http://forum.modtronix.com/index.php?topic=802.msg2891#msg2891

if you have not touched the firmware and the code does not work

have any problem with your NETWORK

test this application

http://www.hw-group.com/download/sw/HerculesSetup.zip




if the same problem continues to reset your MXBOARD with the default values

Connect your MXBOARD with a "cross-over" cable and try again


byee.



11
Programming / Re: Noob question
« on: May 02, 2008, 08:37:56 AM »
Hi

   
I do not understand what you need to do, but attempts to help:

 -> if your problem is turned on or off a PIN:
     
    1)configure TRIS reg.  0=output 1=input
 
    2) set your  LAT reg.  0=Off  1=On

      exp.:

                TRISF_RF4 = 0;     (PIN5 PORTF  set output)
                LATF4 = 1;           (PIN5 LATF    set ON)
 
     The LAT and PORT refer to the same peripheral

     but to read the value of a peripheral, we recommend the use of LATCH port

  -> if you want to know because people modtronix uses "XOR(^)" operator to turn on and off a LED:

          " LATB6 ^= 1; "
 
           if  LATB6=0 :    0 ^ 1 = 1;

                                 0 ^ 0 = 0;


           if  LATB6=1 :    1 ^ 1 = 0;

                                  1 ^ 0 = 1;
         
 
      I personally prefer the operator "NOT(~)":
         
          TRISF_RF4 = 0;
       
          LATF4 = ~LATF4;

          simply reverse the value at the bit

I hope you serve.

byee.

13
Programming / Re: Noob question
« on: April 30, 2008, 08:09:05 PM »
Hi,

Quote
This is the code that flashes the system LED once every second, so I put a LED on F4 that I can toggle on the web interface, but it won't compile.

that is what you said the compiler?


Quote
Also given that I have the SPI LCD how to I use this function call
Code:

void lcdPutString(BYTE* s)


Would it be something like:

Code:

BYTE s = "sting\0"
lcdPutString(s);

declare:
char s[]="mybotnet";

call:
lcdPutString((BYTE*)s);  //force
or lcdputString(s);         //free parse

Quote
I did some C++ some time ago but my main language is java.
   
pointers are specific to C \ C + +, but in my opinion is very important to know how they work
http://en.wikipedia.org/wiki/Pointer

Byee.

14
Ethernet Boards (8-bit) / Re: SMTP module for sending Emails
« on: April 30, 2008, 06:55:37 PM »
hi Mick93,

   
if copies files "dns.c" and "dns.h" in the project folder ....

"linker" ceased to scream

byee.


15
Ethernet Boards (8-bit) / Re: No javascript
« on: March 23, 2008, 06:50:24 AM »
Hi,


If you want to activate a pin is very simple
Only you must send the command method with the "GET" a form
Or a static link with the value:

Quote from: testform.html document
<html>
 <head><title>Test HTML send command</head>
 <body>
   <center>
   <h1>Test FORM with GET Method</h1>
   <form method="get"  action="mypage.cgi" >
      Reset Board ("r=reset" ):&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<input type=text name="m" /><br />
      PIN B1 (1=ON or 0=OFF):<input type=text name="B1"/><br />
      PIN B2 (1=ON or 0=OFF):<input type=text name="B2"/><br />
      PIN B3 (1=ON or 0=OFF):<input type=text name="B3"/><br />
      <input type=submit Value="Send">
   </form>
   <br /><br />
   <h1>Test Link Direct command with GET Method</h1>
   <a href="mypage.cgi?m=r">Reset Board!</a><br />
   PIN B1: <a href="mypage.cgi?B1=1"> [ ON ] </a>&nbsp;&nbsp;  <a href="mypage.cgi?B1=0"> [ OFF ] </a><br />
   PIN B2: <a href="mypage.cgi?B2=1"> [ ON ] </a>&nbsp;&nbsp;  <a href="mypage.cgi?B2=0"> [ OFF ] </a><br />
   PIN B3: <a href="mypage.cgi?B3=1"> [ ON ] </a>&nbsp;&nbsp;  <a href="mypage.cgi?B3=0"> [ OFF ] </a><br />
 </center>
 </body>
</html>

Rename file testform.html.txt  with testform.html

Byee.

Pages: [1] 2 3 ... 10